Gypbond Pro

Product name

Gypbond Pro

Product type

Bonding agent. A green, water-based product with grit. German polymers and formulation.

Use

Apply to smooth concrete (Mivan, RCC and precast) before gypsum plaster.

Uses advised against

Do not use it as a waterproofing product. Do not use it on a wall with seepage. Do not dilute it.

Packs

1 kg, 5 kg, 10 kg and 20 kg buckets.

Shelf life

1 year, in the closed original bucket.

Supplier

Sai India Gypsum Products Pvt. Ltd.
709 & 710, Goodwill Infinity, Sector 12, Kharghar, Navi Mumbai 410210, India

Place of manufacture

Panvel, District Raigad, Maharashtra, India

Phone

7400 1800 20 (Monday to Saturday, 10 am to 7 pm)

Email

Emergency phone number

7400 1800 20, Monday to Saturday, 10 am to 7 pm. At other times use the numbers in the next line.

Medical emergency in India

Call 112. Poison information: National Poisons Information Centre, AIIMS, New Delhi, 1800 116 117 (24 hours).

Classification

Not classified as hazardous under the United Nations GHS. Basis: the supplier of the polymers states that they are safe and do not irritate. No toxicological test was made on the finished product.

Label elements

No pictogram, no signal word and no hazard statement.

Precautions

Handle the product with care all the same. Wear gloves and eye protection. Wash the product off the skin. Do not swallow it. Keep it out of the reach of children.

Alkaline

The product is mildly alkaline: pH 9 (in-house lab test).

Other hazards

A spill makes the floor slippery.

Type of product

Mixture: a polymer dispersion in water with mineral filler and grit.

Formulation

The formulation is a trade secret of the company. This section lists only the ingredients that are classified as hazardous.

Polymers

From a leading German supplier. The supplier states that the polymers are safe and do not irritate.

Hazardous ingredients

None that is classified as hazardous, on the basis of the statement of the supplier of the polymers.

Preservative

Typical for water-based products of this kind (published sheets): a very small quantity of preservative keeps the product good in the bucket.

Crystalline silica (quartz)

CAS number 14808-60-7. The grit and the filler are minerals. Their quartz content is not tested. In the wet product the grit is bound and makes no dust.

Eyes

Rinse immediately with much clean water for at least 15 minutes with the eyelids open. Remove contact lenses if this is easy. Get medical advice if the irritation continues.

Skin

Remove clothing that is wet with the product. Wash the skin with soap and water before the product dries. Get medical advice if redness or a rash occurs.

Breathing

Move the person to fresh air. Get medical advice if the person feels unwell.

Swallowing

Rinse the mouth. Do not cause vomiting. Get medical advice and show the bucket label or this sheet.

Note for the doctor

Treat the symptoms. Published sheets of products of this kind give no specific treatment.

Flammability

The product is water-based. Typical for products of this kind: the wet product does not burn.

Flash point

Not applicable (typical for water-based products of this kind).

Extinguishing media

Use the media that are correct for the fire around the product: water spray, foam, dry powder or carbon dioxide.

Special hazards

The dry film and the plastic bucket can burn. They give smoke, carbon monoxide and carbon dioxide.

Advice for fire-fighters

Wear the usual protective clothing and breathing apparatus. Cool closed buckets with water spray.

Personal precautions

Wear the protection given in section 8. Keep people away from the wet area: the floor is slippery.

Containment

Stop the leak if this is safe. Hold the liquid back with sand, earth or another material that absorbs.

Clean-up

Collect the material with a shovel into a container that closes. Wash the area with water after the bulk is removed. Collect the wash water where this is possible.

Environment

Do not let the product run into drains, water or soil.

Handling

Stir before use with a clean rod. Avoid contact with the eyes and the skin. Do not eat, drink or smoke during the work. Wash your hands after the work.

Opened bucket

Close the bucket after use. General practice for products of this kind: use an opened bucket soon.

Tools

Wash the roller and the brush with water immediately after use.

Lifting

A full bucket weighs up to 20 kg. Lift it with a straight back, or with two persons.

Storage

Store in the closed original bucket, upright, in a covered place, away from direct sun and from heat. Do not let it freeze.

Storage temperature

Typical for water-based polymer products (published data sheets): between 5 °C and 35 °C.

Shelf life

1 year, in the closed original bucket.

Exposure limits

Typical for products of this kind (published sheets): no exposure limit is given for the product. The Second Schedule of the Factories Act 1948 has no entry for a product of this kind.

Dust from the dry coat

If you grind or remove the dry coat, the dust can contain quartz from the grit. The Factories Act 1948 limits such dust. Respirable dust: 10 ÷ (% respirable quartz + 2) mg/m³.

Ventilation

Work with good ventilation.

Eye protection

Wear safety goggles where the product can splash.

Hand protection

Wear waterproof gloves. Typical for products of this kind: gloves of nitrile rubber or butyl rubber.

Skin protection

Wear clothing that covers the arms and legs.

Breathing protection

Not necessary when you apply the product by roller or brush with good ventilation (typical for products of this kind).

Hygiene

Wash the skin before the product dries. Do not use solvents to clean the skin.

Form

Water-based liquid with grit.

Colour

Green.

Odour

Typical for products of this kind: a slight smell of polymer or of ammonia.

pH

9 (in-house lab test).

Density

1.39 g/cc, as packed (in-house lab test).

Viscosity

1,02,000 cps (in-house lab test).

Solids content

58% (in-house lab test).

Boiling point

About 100 °C, as water (typical for water-based products).

Freezing point

About 0 °C, as water (typical for water-based products).

Flash point

Not applicable (typical for water-based products of this kind).

Solubility in water

Can be mixed with water while it is wet. Typical for products of this kind: the dry film does not dissolve in water.

Volatile organic compounds (VOC)

Not measured for this product.

Stability

Stable in the closed bucket in the storage conditions of section 7.

Conditions to avoid

Frost and strong heat. Do not let the product dry in the bucket.

Incompatible materials

Typical for products of this kind (published sheets): strong oxidising agents.

Hazardous decomposition products

None in normal use. In a fire: see section 5.

Tests on this product

No toxicological test was made on this product. The lines below come from published sheets of water-based bonding agents of this kind.

Acute toxicity

Typical: low. Published sheets do not classify products of this kind as acutely toxic.

Eye and skin irritation

The supplier of the polymers states that they do not irritate. The product is mildly alkaline (pH 9). Typical for products of this kind: contact can cause mild irritation of the eyes and the skin for a short time. Rinse the product off.

Sensitisation

Typical for water-based products of this kind: some preservatives can cause a skin allergy in persons who are sensitive to them. Wear gloves. If a rash occurs, stop the work and get medical advice.

Long-term effects

Typical: none known for the wet product. Dust from the dry coat: see section 8.

Ecotoxicity

No test was made on this product. The product is not classified as hazardous to the environment.

Persistence and degradability

Typical: the polymer does not break down quickly. The mineral filler and the grit are inorganic.

Precaution

Do not let the product or the wash water run into drains, rivers, ponds or soil.

Product

Do not pour the product into a drain. Give liquid product that you cannot use to an authorised waste collector.

Small residues

Let a small residue dry in the open bucket, then dispose of it as solid waste in agreement with the local rules.

Packaging

Empty and scrape the bucket. Reuse it or give it for recycling.

Rules in India

The empty plastic bucket: the Plastic Waste Management Rules 2016. Dry product on site debris: the Construction and Demolition Waste Management Rules 2016. The local body can add its own rules.

Classification

Not dangerous goods for transport by road, rail, sea or air (UN Model Regulations, ADR, RID, IMDG Code, IATA).

UN number, class, packing group

None.

Precaution

Transport the buckets closed and upright. Protect them from direct sun and from frost.

Classification and label

Not classified. No hazard label. See section 2.

Indian chemical safety rules

Water, mineral filler and polymers are not in the list of hazardous chemicals of the Manufacture, Storage and Import of Hazardous Chemical Rules 1989 (Schedule 1, Part II).

Test methods

Pull-off strength: ASTM D7234 and ASTM C1583. See the technical data sheet.

Document number

SIG-SDS-03

Revision

1.0

Date

6 October 2026

Approved by

Sudhesh Kumar, QC Head

Format

The 16 sections of the United Nations GHS safety data sheet.

Sources

Product data and in-house lab tests of Sai India Gypsum. The statement of the supplier of the polymers. Published safety data sheets and product data of water-based bonding agents for plaster and of polymer dispersions. The Factories Act 1948 (Second Schedule). The Indian rules named in sections 13 and 15.

Words in this sheet

"Typical", "literature" and "published sheets" mark a value that comes from published safety data sheets of the same kind of product, or from the literature on the base material. Such a value is not a test result of this product.

Notice

The information is given in good faith for the safe handling, storage and disposal of the product. It is not a specification and not a guarantee of a property. The user must check that the product is fit for his use.