Sai India Gypsum Get a quote
Menu

Products

SIG-MRGypsum plaster
PlastoPlusOne-coat gypsum plaster
Gypbond ProBonding agent
Pro Max boardGypsum board

Company

AboutSince 2002
ResourcesGypsum plaster explained
DownloadsData sheets and test reports
ContactKharghar, Navi Mumbai

This page

Get a quote
PlastoPlus

PlastoPlus · One-coat gypsum plaster

One kilo.
One square foot.

Proved on our customers’ sites.

Get a quoteWhatsApp us
20
sq ft
one 20 kg bag · 13 mm

The highlights.

1 kg.
1 sq ft.
At 13 mm. Proved on our customers’ sites.
QR on every bag.
Scan it. Read the test certificate of your batch.
93%+ white.
Less putty. Brighter paint.
15 minutes.
Final set.
5.85 N/mm².
Bending strength. Over 11 times the IS minimum.
One coat.
6 to 20 mm in a single coat.
No water curing.
Plaster today. No watering after.
Faster site.
No curing wait before the next trade.
Does not burn.
Gypsum is non-combustible.
Lighter.
Less load than sand-cement plaster.
Low heat flow.
Gypsum conducts little heat.
Made at Panvel.
Since 2021.

Planning

The easiest sum on site.

Your wall in square feet is your plaster in kilos. At 13 mm.

1,000
sq ft of wall
1,000
kg of PlastoPlus
50
bags of 20 kg
0102020 kg
The plaster from one 20 kg bag of PlastoPlus: 20 kilosOne coat: 6 to 20 mmEach square is one square foot. At 13 mm, one kilo of PlastoPlus covers one square foot, so one 20 kg bag covers 20 squares. Proved on our customers’ sites. A thinner coat covers more, a thicker coat less: half the thickness gives twice the area. The thickness is drawn larger than true.

The finish

White. Flat. Smooth.

A white plastered room
White.
A straightedge on a plastered wall
Flat.
A trowelled plaster surface, close up
Smooth.

Compare

Less plaster.
Same wall.

1,000 sq ft at 13 mm.

PlastoPlus
1,000
kg · 50 bags of 20 kg
Buildon One Coat
1,375
kg · 55 bags of 25 kg

375 kg less to buy and carry up.

Get a quote for 50 bagsEnter your own plaster ›

White, and it goes far.

Wall from one kilo, and whiteness, as each brand publishes them.

Plaster
Wall from one kilo, sq ft
Whiteness
SIG-MR
1.08
93%+
Gyproc Elite 100 ↗
1.08
—
PlastoPlus
1.00
93%+
Gyproc Elite 90 ↗
0.96
—
Magicrete Elite ↗
0.85–0.92
—
Gyproc Elite MR ↗
0.88
—
Gyproc Xpert+ ↗
0.88
—
Buildon One Coat ↗
0.74
92%
Buildon Classic ↗
0.74
70–80%
Buildon Imported ↗
0.74
85%
Buildon Master ↗
0.74
85%
Gujarat gypsum plaster
0.70–0.75
75–85%
Rajasthan gypsum plaster
0.70–0.75
65–75%
Walplast GypEx Silver Plus ↗
0.62–0.77
> 85%
JK GypsoMaxX 301 ↗
0.62–0.68
approx. 90%
JK GypsoMaxX 101 ↗
0.49–0.55
approx. 94%

Other brands: as each one publishes on its own site. The mark ↗ beside a brand opens that document (read on 23 September 2026). — means no figure is published. A range is drawn at its midpoint. Rajasthan and Gujarat plasters are unbranded: their figures are what we see in the market (14 to 15 sq ft from a 20 kg bag).

Whiteness

A whiter base needs less putty and gives paint a brighter colour.

The same paint on a PlastoPlus base and on a greyer Rajasthan or Gujarat base
PlastoPlus base
Rajasthan / Gujarat base

The same paint on both.

93%+
whiteness

Strength

Sets hard.

Over 11 times the IS 2547 minimum in the bending test.

5.85N/mm²

Bending (transverse) strength. IS 2547 minimum: 0.49 N/mm².

15.08N/mm²

Compressive strength.

0.495.85 N/mm²
A set bar of PlastoPlusIS 2547: at least 0.49 N/mm²A three-point bending test. A bar of set PlastoPlus rests on two rollers, and a third roller presses down in the middle until the bar breaks. The stress at the break is the bending (transverse) strength: 5.85 N/mm² in our factory lab. IS 2547 asks at least 0.49 N/mm².

Fineness

Fine powder.
Smooth trowel.

Under 2 parts in 100 stay on the sieve. The standard allows 5.

< 2%

Left on a 150 µm sieve. IS 2547 limit: 5%.

0 %5 %10 %150 µm
PlastoPlus powderIS 2547: at most 5 % may stay on the sieveA fineness test. A sample of PlastoPlus powder is shaken on a sieve with 150 µm openings. The fine powder falls through to the pan; what stays on the sieve is weighed. For PlastoPlus it is under 2 % in our factory lab. IS 2547 allows up to 5 %. Lower is finer, and a fine powder trowels smooth.

Setting time

Set in 15 minutes.

Mix what the crew can place in one go.

15min

Final set of a test sample. IS 2547 range: 10 to 30 minutes. Site time depends on water, batch and weather.

VICAT
The needle and the plasterIS 2547: final set in 10 to 30 minutesA Vicat apparatus. Every two minutes the needle drops into the plaster in the ring, each time in a new place. While the plaster is soft, the needle sinks in. As it sets, the needle sinks in less. When the needle no longer sinks in, the plaster has reached its final set: 15 minutes for SIG-MR and PlastoPlus in the test. The time on site depends on the water, the batch and the weather.

Our lab. Our factory.

Scan the bag.
Read its test.

The QR code on every bag opens the test certificate of that batch. Checked in our own lab before it leaves Panvel.

Test certificate
PlastoPlus · Batch GPX5V12Q · 09/26
AppearanceFree-flowing powder
Whiteness94.6%
Initial setting4 min
Final setting15 min
Workability11 min
pH6.5
Exothermic temperature50.7 °C
The results of one batch, as on its certificate. Open this certificate ›

On the wall

Straight onto brick and block.

On Mivan and RCC, Gypbond Pro goes on first.

A mason applies PlastoPlus on an AAC block wall
01
Clean
No dust. No oil.
02
Prime
Mivan and RCC only.
03
Measure
1 water : 1.25 plaster.
04
Mix
Until smooth.
05
Apply
One coat. 6–20 mm.
06
Finish
Level. Trowel.

Properties

Fourteen properties.
All measured.

Tested in our own lab at the Panvel factory, on production batches. Green is the band that IS 2547 allows.

Coverage
1.00sq ft/kg
One kilo, one square foot. At 13 mm.
Customer sitesFactory lab
Whiteness
93%+
A brighter base for paint.
Every batch: above 93%Factory lab
Final set
15min
Inside the IS band.
IS 2547: 10–30 minFactory lab
Initial set
4min
Starts to stiffen.
Our range: 2–4 minFactory lab
Workability
11min
Time to work the mix, in our test.
Our range: 8–16 minFactory lab
Bending strength
5.85N/mm²
Over 11 times the IS minimum.
IS 2547: ≥ 0.49Factory lab
Compressive strength
15.08N/mm²
Hard when set.
Factory lab
Fineness
< 2%
Left on a 150 µm sieve. Lower is finer.
IS 2547: ≤ 5%Factory lab
Surface hardness
3.4mm
Ball indentation. In the final-coat band.
IS 2547: 3.0–4.5 mmFactory lab
Expansion
0.14%
Barely moves as it sets.
IS 2547: ≤ 0.2%Factory lab
pH
6.5
Near neutral.
Our range: 6–8Factory lab
Heat on setting
50.7°C
Peak temperature as it sets.
Our range: 45–53Factory lab
Dry bulk density
780kg/m³
Powder, as packed.
Our range: 600–800Factory lab
Normal consistency
43%
Water for a workable mix.
Factory lab

Two plasters. One plant.

PlastoPlus or SIG-MR?

PlastoPlus
SIG-MR
Bag
20 kg
25, 20, 15 kg
Wall from one kilo
1.00 sq ft
1.08 sq ft
Whiteness
93%+
93%+
Final set
15 min
15 min, or up to 30 to order
Ask for both in one quotationSee SIG-MR ›

Your wall. Your plaster.

Check it yourself.

Enter your plaster. See the bags and the cost.

PlastoPlus
Bag20 kg
Coverage20 sq ft at 13 mm
Bags—
Plaster—
Cost of this wall—
Cost per sq ft—
Bags—
Plaster—
Cost of this wall—
Cost per sq ft—

Enter the coverage of your plaster.

We show no prices: you type the price you were quoted. Bags are whole bags. Coverage at another thickness is scaled in proportion. PlastoPlus: 20 sq ft from a 20 kg bag at 13 mm.

Pack

One pack. 20 kg.

PlastoPlus 20 kg bag
QUICK CASH
₹10 to ₹100
A coupon in every bag.Scan it in our Quick Cash app. More than 10,000 contractors use it.
Get the app
Get a quoteWhatsApp 7400 1800 20

Shelf life 12 months. Store in a dry place.

Made at Panvel since 2021. Supplied ex-factory to any place. No minimum order.